Portable Gas Detector Accessories MANUFACTURED BY STATUS SCIENTIFIC CONTROLS Gas sampling accessories for use with the PGD2 & PGD3-IR Series of Portable Gas Detectors. 

Hand Aspirated Probe (Stock No.SS089) 
 
Click on the picture to enlarge. 
 
This aspirator is normally intended for use with Portable Gas Detectors without an internal pump. It comprises a hand operated pump, tubing (3 metres standard), filter, ball float and sampling adaptor/s which fit into the gas sensor inlets of the instrument. 
 
It is used drawing in gas samples from below ground level. The ball float at the end of the tube is specially designed to prevent water being sucked into the tube in situations where there is water at the bottom of the entry into which the tube is inserted. 
 
The aspirator is operated by connecting the sampling adaptor/s into the gas inlet/s of the instrument, making sure that they are fully inserted. Locate the tube at the desired sampling point. Squeeze the aspirator bulb fully and then release. Wait until the bulb has returned to its normal shape then continue sampling in the above manner for a minimum of 3 squeezes per metre of tube. 
Standard Pump Sampling Kit (Stock No.'S SS113-03 And SS113-10) 
 
Click on the picture to enlarge. 
 
This is the standard sampling kit that is supplied with Portable Gas Detectors that are fitted with an internal pump. It consists of a ball float, tubing and sampling adaptor/s which fit into the gas sensor inlets of the instrument. 
 
Available in two standard tube lengths:- 
3 Metre - Stock No. SS113-03 
10 Metre - Stock No. SS113-10 
Standard Flexible Probe (Stock No.SS114) 
 
Click on the picture to enlarge. 
 
This probe is for use with Portable Gas Detectors that are fitted with an internal pump. It consists of a flexible probe, filter, tubing and sampling adaptor/s which fit into the gas sensor inlets of the instrument. 
Aviation Fuel Flexible Probe (Stock No.SS118) 
 
Click on the picture to enlarge. 
 
This probe is for use with Portable Gas Detectors fitted with an internal pump and sensors for the detection of aviation fuels. It consists of a flexible probe, filter, tubing and sampling adaptor/s which fit into the gas sensor inlets of the instrument. 
Hand Aspirated Flexible Probe (Stock No.SS119) 
 
Click on the picture to enlarge. 
 
This aspirator is normally intended for use with Portable Gas Detectors without an internal pump. It comprises a hand operated pump, tubing, filter, flexible probe and sampling adaptor/s which fit into the gas sensor inlets of the instrument. 
 
It is used drawing in gas samples from the tip of the probe by pointing the probe at the area being sampled e.g. around a pipe flange. 
 
The aspirator is operated by connecting the sampling adaptor/s into the gas inlet/s of the instrument, making sure that they are fully inserted, and then probing into the area under test. Squeeze the aspirator bulb fully and then release. Wait until the bulb has returned to its normal shape then continue sampling in the above manner for a minimum of 3 squeezes per metre of tube. 
Biogas Sampling Kit (Stock No.SS112) 
 
Click on the picture to enlarge. 
 
This probe is for use with the Biogas version of Portable Gas Detector. It consists of a conical steel probe, filter, tubing and pressure regulator/adaptor which fit into the gas sensor inlet of the instrument. The probe fits into the wall of the Biogas vessel and relies upon the internal pressure within the vessel to force the sample into the gas detector inlet. The pressure regulator can be used to adjust the pressure in order to prevent over pressurisation of the gas sensors which could otherwise cause erroneous readings. 
For Quality Gas Detection at Competitive Prices Contact 
sales@status-scientific.com 
International - +44 (0) 1623 651381 
For Quality Gas Detection at Competitive Prices 
 
Contact 
 
sales@status-scientific.com 
 
International - +44 (0) 1623 651381